濟南伸縮蓬廠

　　1、必須按施工圖放樣，放樣和號料時一定要預留焊接收縮量和加工余量，然后根據放樣作樣板；對于鋼材的矯正，鋼材下料前必須先進行矯正，矯正后的偏差值不得超過規范規定的允許偏差值.

　　1, must according to the construction lofting, lofting and materials must be reserved for welding and machining allowance, and then make the model according to the layout of the steel; correction, steel cutting must be carried out before the correction, after the error correction value deviation shall not be allowed to exceed the specification value.

　　這樣方可保證下料的質量；熱加工的型鋼先熱加工，待冷卻后再號孔；鋼板預埋件及其他零件切割鉆孔及噴防腐漆處理。

　　It can ensure the quality of steel material; thermal processing of the first heat processing, after cooling to the hole; cutting steel embedded parts and other parts of drilling and anti-corrosion spray paint processing.

　　2、遮陽篷的懸掛臂安裝要采用焊接，同時還需檢查焊接節點，調節懸掛臂設計坡度，確定無誤后方可進行焊接.

　　2, the awning hanging arm installation to be welded, but also need to check the welding node, adjust the design of the suspension arm slope, determine the error before welding

　　靠邊一條懸掛臂準確無誤后，安裝另一邊一條懸掛臂，就位準確后方可點焊；以這兩條懸掛臂為基準拉出懸掛臂的最高、最底標高線，一一焊接剩余懸掛臂，并焊接無縫鋼管.

　　Pull a suspension arm after the accurate installation on the other side of a hanging arm, accurate positioning before spot welding; these two suspension arms based out of suspension arm the highest and the bottom elevation line, one welding residual suspension arm, welded and seamless steel pipe.

　　型鋼需接長時先焊接頭并矯直，采用型鋼接頭時，為了使接頭型鋼與鋼板預埋件緊貼，必須按設計要求鏟去楞角；對接焊縫應在焊縫的兩端焊上引弧板，其材質和波口型式與焊件相同，焊后氣割切除并磨平。

　　Steel need to take a long time before welding and straightening, with steel joints, in order to make the joints of steel and steel embedded parts must be close to, according to the design requirements of shovel to corners; butt welds shall be arc plate at both ends of the weld, the material and the wave mouth type and welding, after welding cutting and grinding removal.

　　公司內部也建立了嚴密的管理體系，能夠向客戶提供高品質各類產品的服務。正是這樣，憑著產品過硬、質量和企業的良好聲譽，本公司贏得了廣大客戶的一致好評與信賴，并建立了長久友好的合作關系。

　　誠邀山東各地市級加盟代理。?

　　歡迎各方客戶前來洽談業務，真誠合作，共創繁榮。?

　　公司:濟南伸縮蓬廠

　　諾商基于多年的優化經驗和品牌基礎推出的諾商商道系統，諾商信息您身邊的互聯網專家！